СтартКопи - сайт о ремонте копиров и принтеров, заправке картриджей

Архив старой Конференции StartCopy

canon irc 3200: e-000732-001

[ Новая Конференция StartCopy ] [ F.A.Q. ] [ Поиск по сайту ] [ Форум ] [ Участники ] [ 1-я страница сайта ]
 
Вопросы можно задавать в новой Конференции СтартКопи
 

0 mariko
msk
00:38 - 12.09
Мануал гласит " E732 - reader communication error"
При этом 732 ошибка с подкодом 001 не упоминается.
Что именно подразумевается под "ридером"?
АДФ? Контроллер?
1 Mishel01®
Butyrka
02:25 - 12.09
Ни то ни другое. Гляньте, что кличется ридером в парткаталожной части мануала.
2 Beto®
08:23 - 12.09
Вариант 1:
E732-0001 Error code A message 'Starting up. Please wait' keeps displaying for about 2 min. 40 sec. after the power is turned ON, and then the error code results (DC power supply unit PCB J158 output failure)











Symptom
About 2 min. 40 sec. after the power is turned ON, a message 'Starting up. Please wait' is displayed and then E732-001 (DC power supply unit PCB J158 output failure) is displayed. (Refer to SymptomExplanation.)

Description
When the power is turned ON, initialization of finisher and feeder should start if the main unit operates normally.

Cause
DC power supply unit PCB (1) failure

Items to Check
1) Check whether DC line is supplied to the fuse PCB J58 from the DC power supply PCB J158. If there is no input, check the DC power supply PCB.
2) Check whether AC line is supplied to the DC power supply PCB. If there is no problem with the AC line input, the DC power supply PCB is likely faulty.

Field Remedy
Perform CheckItem and replace the DC power supply PCB, if faulty.

FG6-8970(100/120V) DC Power Supply PCB Ass'y
FG6-8971(220/240V) DC Power Supply PCB Ass'y
3 Beto®
08:24 - 12.09
Вариант 2:
E732-0001 Error code A message 'Starting up. Please wait' keeps displaying for about 2 min. 40 sec. after the power is turned ON, and then the error code results

Symptom
About 2 min. 40 sec. after the power is turned ON, the message 'Starting up. Please wait' is displayed and then E732-001 is displayed.

Cause
DC output failure from the DC fuse PCB J67

Items to Check
1) Check whether the lattice connector of the interface cable is securely inserted. The lattice connector connects the reader and the printer (located at the back).

2) Check whether the wiring from the lattice connector to the distribution board J67 is secured.

3) Check whether DC line is output from the fuse PCB J67.

4) If no, check whether DC line is output to the fuse PCB J53, J56, J57 and J58 from the DC power supply PCB. If yes, the fuse PCB Ass'y is likely faulty.

Field Remedy
Perform CheckItem and replace the fuse PCB ass'y, if faulty.

FG3-2337 Fuse PCB Ass'y
4 Beto®
08:25 - 12.09
Вариант 3:
E732-0001: Lattice cable that connects scanner to printer has poor contact

[ Case in the field ]
Description
Since refitting and replacement of flat cables (RCON-I/F 1 and RCON-I/F 2) did not solve the error code "E732-0001", the lattice cable was replaced with a new one for solution.
- E732-0001 can be displayed when an error is detected during communication between the reader and the printer after power-on (bad connection between the reader and the printer).

Field Remedy
1. In service mode > COPIER > Display > VERSION, check the version number displayed next to "R-CON."
2. If the version number is not displayed, refit the interface cables between the reader and the printer.
3. If the symptom still occurs, replace the lattice cables with new ones.
FM2-0035 Lattice Cable

(0)А говоришь нет ничего.
5 mariko
msk
13:24 - 12.09
Значит, или я слепая, или мануал не совсем полный.
Спасибо. Попробую победить его.

33923392
СтартКопи - сайт о ремонте копиров и принтеров, заправке картриджей


Рейтинг@Mail.ru Rambler's Top100