Коды ошибок Коды ошибок копировальных аппаратов Toshiba копировальных аппаратов Toshiba
Если Ваш копировальный аппарат Toshiba выдал на индикации некий код, то узнать причину возникновения ошибки Вы можете в этом разделе.
Но код ошибки - это лишь следствие сбоя в работе аппарата; а о том, как устранить сам сбой, есть много материалов в разделах "Ремонт", "Ликбез", "FAQ"; также Вы можете воспользоваться поиском или указателем материалов сайта
Toshiba 1210
Код ошибки
Описание
C1
Copy table position error
C2
Paper is not fed from the tray when the copy table starts moving
C3
Copy table drive error
C4
Copy table position error
C5
Copy table end position error
C6
Copy table position error at the end of the copy cycle
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8
Thermofuse blown
CP
Main drive overloaded
CA
Main Board defective
E1
Paper jam
E2
Fuser jam
E3
Paper jam at start-up
E5
Paper jam in the tray
E7
Paper jam in the registration area
Toshiba 1310
Код ошибки
Описание
C5
Copy table drive overloaded
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CE
EPROM defective or missing
CP
Main drive overloaded
CD
EPROM end of life
CF
Development unit not properly installed or defective
E0
Used toner collection bottle full
E1
Paper jam
E2
Fuser jam
E3
Paper jam at start-up
E5
Paper jam in the tray
E6
Paper jam at by-pass or defective sensor
Toshiba 1340, 1350
Код ошибки
Описание
C5, C6
Scan problem
C7
Fuser problem (reset with 0 + 8 mode, code 89)
CE
Missing EEPROM
CF
Board problem
CP
Drive problem
E1
Paper jam
E2
Fuser jam
E3
Paper jam
E5
Paper feed jam
E0
Toner waste bottle is full
Toshiba 1550
Код ошибки
Описание
C01
Main motor drive problem
C21
Optics problem Scan , lens, mirror
C26
Exposure lamp detect problem
C32
Setup error (UA)
C41
Fuser thermistor, or no heat
C43
Fuser thermistor problem or other fuser problem, after machine goes into ready
C44
Heater problem
C54
Communication problem between sorter and machine main board
C55
Communication problem between ADF and machine main board
C71
ADF drive problem
C72
ADF registration sensor problem
C73
EEPROM initialization problem
C81
Sorter paper conveying motor
C82
Sorter bin motor
C83
Sorter upper sensor
C84
Sorter lower sensor
C85
Sorter home sensor
C86
Sorter copy removal sensor
C94
Optics initialization problem in test modes
E01
Paper jam
E02
Fuser jam
E03
Paper jam at startup
E05
Paper jam in the registration area
E14
Lower cassette jam
E71, E72, E73
ADF jam
E75
ADF jam of 2nd original
E81, E82
Sorter jam
Toshiba 1560
Код ошибки
Описание
C01
Main motor drive overloaded
C21
Optics problem Scan , lens, mirror
C26
Exposure lamp blown, or bad contacts
C32
Easy set-up error
C41
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C43, C44
Abnormal temperature in the fuser, thermistor error
C54
Communication with the sorter is intrerrupted
C55
Communication with the feeder is intrerrupted
C71
Top Feeder motor overloaded
C72
Sensor problem in the feeder
C73
Feeder EPROM initialization error
C81
Sorter paper transport motor overloaded
C82
Sorter shift tray motor overloaded
C83
Upper position error in the sorter
C84
Lower limit position error in the sorter
C85
Home position error in sorter
C88
Paper sensor error in sorter
C94
Optical system initialization error
E01
Paper jam
E02
Fuser jam
E03
Paper jam at startup
E05
Paper jam in the registration area
E14
Paper jam in the Paper Feed Unit
E71
Original jammed in the top feeder
E72
Original jammed during transport in the top feeder
E73
Original jam at the feeder exit
E75
Original jammed
E81, E82
Sorter jam
Toshiba 1650
Код ошибки
Описание
A4
Sorter problem
A5
Communication problem between main CPU and IPC
A6
Sorter interface problem
C2
Communication problem between CPU's
C5
Scan or optic problem. Locked up or won't initialize or return to home position
C7
Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CF
Developer calibration problem
CP
Drive problem
E1
Paper jam
E2
Fuser jam
E3
Paper jam
E4
Front door opened during copy cycle
E5
Paper feed jam
Toshiba 1710
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC
ADF jam
ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 2050
Код ошибки
Описание
A4
Sorter problem
A5
Communication problem between main CPU and IPC
A6
Sorter interface problem
C2
Communication problem between CPU's
C5
Scan or optic problem. Locked up or won't initialize or return to home position
C7
Fuser problem. After repairing problem, go to "0 & 8 mode", code 87 to reset
CF
Developer calibration problem
CP
Drive problem
E1
Paper jam
E2
Fuser jam
E3
Paper jam
E4
Front door opened during copy cycle
E5
Paper feed jam
Toshiba 2060
Код ошибки
Описание
C01
Main motor drive problem
C04
Pedestal main drive problem
C05
Duplex drive problem
C11
Duplex exit motor
C12
Duplex end motor
C13
Upper cassette
C14
Lower cassette
C15
Pedestal upper cassette
C16
Pedestal middle cassette
C17
Pedestal lower cassette
C18
LCT
C21
Scan problem
C22
Lens problem
C23
Mirror motor
C26
Exposure lamp
C27
Scan motor
C33
Set up failure
C35
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41
Fuser thermistor or low temperature
C43
Fuser problem after warm-up
C44
Fuser problem after warm-up
C45
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01
Jam
E02
Fuser jam
E03
Jam at turn on
E04
Front door opened during copy cycle
E05
Registration jam
E08
Duplex unit jam
E11
Duplex jam
E12
Bypass jam
E13
Upper cassette jam
E14
2nd cassette jam
E15
3rd cassette jam
E16
4th cassette jam
E17
4th cassette jam
E19
CT jam
E21
LCT jam
E22-E25
Paper jams in copier
E71
ADF feed jam
E72
ADF transport jam
E73
ADF exit jam
E74
RADF jam
E75
ADF 2nd original jam
E81-E85
Sorter jam
E88
Jam after sorter
Toshiba 2310
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC
ADF jam
ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 2500
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC
ADF jam
ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 2510
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC
ADF jam
ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 2532
Код ошибки
Описание
A4
Sorter problem
A5
Communication problem with main board
A6
Communication problem with sorter
A7
Communication problem with ADF
A9
Exposure lamp problem or auto exposure problem
C2
Communication problem between main board
C5
Scan won't initialize or won't move
C7
Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CC
ADF belt motor or exit motor not turning
CF
Auto toner adjustment did not take
CP
Drive problem in machine
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy cycle
E5
Feed jam
Toshiba 2540
Код ошибки
Описание
A4
Sorter problem
A5
Communication problem with main board
A6
Communication problem with sorter
A7
Communication problem with ADF
A9
Exposure lamp problem or auto exposure problem
C2
Communication problem between main board
C5
Scan won't initialize or won't move
C7
Fuser problem: To clear fuser code, go to 0 & 8 mode, code 89
CC
ADF belt motor or exit motor not turning
CF
Auto toner adjustment did not take
CP
Drive problem in machine
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy cycle
E5
Feed jam
Toshiba 2550
Код ошибки
Описание
A2
Duplex functional problems
A4
Sorter problem
A5
Communication lost with the sorter
A6
Communication problems with the sorter interface
A7
Communication problems with the feeder
A9
Exposure lamp blown, or bad contacts
C2, C3
Processor to subprocessor communication problems
C5
Optical system initialization error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CB
Original feed motor overloaded in the feeder
CC
Original transport motor overloaded in the feeder
CF
Toner density error
CP
Main motor drive overloaded
E1
Paper jam detected in machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E4
Front cover open during copy cicle
E5
Paper feed jam in the paper tray
E8
Paper jam in the duplex unit
E9
Paper jam in the optional paper feed unit
EC
Original misfeed in the feeder
ED
Original jam in the feeder
EE
Original jam at the feeder inverter or exit area
Toshiba 2810
Код ошибки
Описание
C1
Scan did not return home
C3
Scan home sensor
C4
Scan problem
C5
Scan limit sensor
C6
Scan did not return
C7
Thermistor or other fuser problem
CC
Scan did not leave home
CP
Drive
E1
Jam inside machine
E2
Fuser jam or exit jam
E3
Exit switch or registration switch
E5
Paper feed jam
E7
Cassette or registration jam
Toshiba 2860
Код ошибки
Описание
C01
Main motor drive problem
C04
Pedestal main drive problem
C05
Duplex drive problem
C11
Duplex exit motor
C12
Duplex end motor
C13
Upper cassette
C14
Lower cassette
C15
Pedestal upper cassette
C16
Pedestal middle cassette
C17
Pedestal lower cassette
C18
LCT
C21
Scan problem
C22
Lens problem
C23
Mirror motor
C26
Exposure lamp
C27
Scan motor
C33
Set up failure
C35
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41
Fuser thermistor or low temperature
C43
Fuser problem after warm-up
C44
Fuser problem after warm-up
C45
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01
Jam
E02
Fuser jam
E03
Jam at turn on
E04
Front door opened during copy cycle
E05
Registration jam
E08
Duplex unit jam
E11
Duplex jam
E12
Bypass jam
E13
Upper cassette jam
E14
2nd cassette jam
E15
3rd cassette jam
E16
4th cassette jam
E17
4th cassette jam
E19
CT jam
E21
LCT jam
E22-E25
Paper jams in copier
E71
ADF feed jam
E72
ADF transport jam
E73
ADF exit jam
E74
RADF jam
E75
ADF 2nd original jam
E81-E85
Sorter jam
E88
Jam after sorter
Toshiba 2870
Код ошибки
Описание
C01
Main motor drive problem
C04
Pedestal main drive problem
C05
Duplex drive problem
C11
Duplex exit motor
C12
Duplex end motor
C13
Upper cassette
C14
Lower cassette
C15
Pedestal upper cassette
C16
Pedestal middle cassette
C17
Pedestal lower cassette
C18
LCT
C21
Scan problem
C22
Lens problem
C23
Mirror motor
C26
Exposure lamp
C27
Scan motor
C33
Set up failure
C35
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41
Fuser thermistor or low temperature
C43
Fuser problem after warm-up
C44
Fuser problem after warm-up
C45
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01
Jam
E02
Fuser jam
E03
Jam at turn on
E04
Front door opened during copy cycle
E05
Registration jam
E08
Duplex unit jam
E11
Duplex jam
E12
Bypass jam
E13
Upper cassette jam
E14
2nd cassette jam
E15
3rd cassette jam
E16
4th cassette jam
E17
4th cassette jam
E19
CT jam
E21
LCT jam
E22-E25
Paper jams in copier
E71
ADF feed jam
E72
ADF transport jam
E73
ADF exit jam
E74
RADF jam
E75
ADF 2nd original jam
E81-E85
Sorter jam
E88
Jam after sorter
Toshiba 3110
Код ошибки
Описание
C1
Copy table start-up position error
C2
The paper does not feed when the copy table starts moving
C3
Paper start position not detected, copy table switch defective
C4
Copy table home position error
C5
Copy table end position error
C6
Copy table reverse movement error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CP
Main motor drive overloaded
E1
Paper jam in the machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E5
Paper jam in the paper tray
E6
Paper jam at by-pass or defective sensor
E7
Paper jam in the feed area or registration
Toshiba 3210
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2, C3
Processor to subprocessor communication problems
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC
ADF jam
ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 3220
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC
ADF jam
ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 3301
Код ошибки
Описание
C1
Copy table start-up position error
C2
The paper does not feed when the copy table starts moving
C3
Paper start position not detected, copy table switch defective
C4
Copy table home position error
C5
Copy table end position error
C6
Copy table reverse movement error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CP
Main motor drive overloaded
E1
Paper jam in the machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E5
Paper jam in the paper tray
E6
Paper jam at by-pass or defective sensor
E7
Paper jam in the feed area or registration
Toshiba 3550
Код ошибки
Описание
A1
Transfer/separator
A2
Duplex problem
A3
PFC CPU malfunction
A4
Sorter problem
A5
Communication problem between main board and IPC
A6
Sorter board to copier communication problem
A7
Communication problem between copier and RADF
A0
Communication main board problem
C3
Communication problem between main board and sub processor
C5
Optics locked or not initialized
C7
Fuser problem. Reset required. Turn off power. Hold "0" & "8" keys while turning on power. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the number keys, press "0". Then press "interrupt". Then press "0" & "9" at the same time
CB
ADF feed motor drive problem
CC
ADF transport motor drive problem
CP
Copier main motor drive problem
E1
Jam
E2
Fuser jam
E3
Jam at turn on
E4
Front door opened during copy cycle
E5
Registration jam
E8
Duplex unit jam
E9
Jam in paper feed unit pedistal
EC
ADF jam
ED
ADF transport jam
EE
ADF exit or reversing jam
Toshiba 3560
Код ошибки
Описание
C01
Main motor drive problem
C04
Pedestal main drive problem
C05
Duplex drive problem
C11
Duplex exit motor
C12
Duplex end motor
C13
Upper cassette
C14
Lower cassette
C15
Pedestal upper cassette
C16
Pedestal middle cassette
C17
Pedestal lower cassette
C18
LCT
C21
Scan problem
C22
Lens problem
C23
Mirror motor
C26
Exposure lamp
C27
Scan motor
C33
Set up failure
C35
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41
Fuser thermistor or low temperature
C43
Fuser problem after warm-up
C44
Fuser problem after warm-up
C45
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01
Jam
E02
Fuser jam
E03
Jam at turn on
E04
Front door opened during copy cycle
E05
Registration jam
E08
Duplex unit jam
E11
Duplex jam
E12
Bypass jam
E13
Upper cassette jam
E14
2nd cassette jam
E15
3rd cassette jam
E16
4th cassette jam
E17
4th cassette jam
E19
CT jam
E21
LCT jam
E22-E25
Paper jams in copier
E71
ADF feed jam
E72
ADF transport jam
E73
ADF exit jam
E74
RADF jam
E75
ADF 2nd original jam
E81-E85
Sorter jam
E88
Jam after sorter
Toshiba 3570
Код ошибки
Описание
C01
Main motor drive problem
C04
Pedestal main drive problem
C05
Duplex drive problem
C11
Duplex exit motor
C12
Duplex end motor
C13
Upper cassette
C14
Lower cassette
C15
Pedestal upper cassette
C16
Pedestal middle cassette
C17
Pedestal lower cassette
C18
LCT
C21
Scan problem
C22
Lens problem
C23
Mirror motor
C26
Exposure lamp
C27
Scan motor
C33
Set up failure
C35
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41
Fuser thermistor or low temperature
C43
Fuser problem after warm-up
C44
Fuser problem after warm-up
C45
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01
Jam
E02
Fuser jam
E03
Jam at turn on
E04
Front door opened during copy cycle
E05
Registration jam
E08
Duplex unit jam
E11
Duplex jam
E12
Bypass jam
E13
Upper cassette jam
E14
2nd cassette jam
E15
3rd cassette jam
E16
4th cassette jam
E17
4th cassette jam
E19
CT jam
E21
LCT jam
E22-E25
Paper jams in copier
E71
ADF feed jam
E72
ADF transport jam
E73
ADF exit jam
E74
RADF jam
E75
ADF 2nd original jam
E81-E85
Sorter jam
E88
Jam after sorter
Toshiba 3701
Код ошибки
Описание
E0
Paper jammed in the machine at power-up
E1
Paper jam in the fusing or transport area
E2
Paper jam in the fusing area
E3
Misfeed at the manual feed table
E6, E7, E8
Copy table drive problem
E9
Copy table reverse clutch not working
Toshiba 3810
Код ошибки
Описание
C5
Scan problem
C7
Heater problem
CD
EEPROM at end of life
CE
EEPROM/main board problem
CF
DV unit out or toner sensor problem
CP
Drive
E1
Paper jam before exit
E2
Exit jam
E3
Jam
E5
Cassette jam
E6
Bypass jam
E0
Waste toner full
Toshiba 3910
Код ошибки
Описание
C5
Scan problem
C7
Heater problem
CD
EEPROM at end of life
CE
EEPROM/main board problem
CF
DV unit out or toner sensor problem
CP
Drive
E1
Paper jam before exit
E2
Exit jam
E3
Jam
E5
Cassette jam
E6
Bypass jam
E0
Waste toner full
Toshiba 4010
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC
ADF jam
ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 4111, 4121
Код ошибки
Описание
C1
Scanner not home
C2
First paper path switch or sub processor
C5
Scan stop switch
C5
Scan won't stop
C7
Fuser problem
C8
Lens
C9
Check 24V
Toshiba 4130, 4140
Код ошибки
Описание
C1
Copy table reverse movement home position error
C2
Paper start position not detected, copy table switch defective
C5
Copy table end position error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8
Lens home position error
C9
5v power supply defective
E1
Paper jam detected in machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E5
Paper feed jam in the paper tray
E7
Paper jam at registration
Toshiba 4501
Код ошибки
Описание
E0
Paper jammed in the machine at power-up
E1
Paper jam in the fusing or transport area
E2
Paper jam in the fusing area
E3
Misfeed at the manual feed table
E6, E7, E8
Copy table drive problem
E9
Copy table reverse clutch not working
Toshiba 4550
Код ошибки
Описание
A2
Duplex functional problems
A4
Sorter problems
A5
Communication lost with the sorter
A6
Communication problems with the sorter interface
A7
Communication problems with the feeder
A9
Exposure lamp blown, or bad contacts
C2, C3
Processor to subprocessor communication problems
C5
Optical system initialization error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CB
Original feed motor overloaded in the feeder
CC
Original transport motor overloaded in the feeder
CF
Toner density error
CP
Main motor drive overloaded
E1
Paper jam detected in machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E4
Front cover open during copy cicle
E5
Paper feed jam in the paper tray
E8
Paper jam in the duplex unit
E9
Paper jam in the optional paper feed unit
EC
Original misfeed in the feeder
ED
Original jam in the feeder
EE
Original jam at the feeder inverter or exit area
Toshiba 4560
Код ошибки
Описание
C01
Main motor drive problem
C04
Pedestal main drive problem
C05
Duplex drive problem
C11
Duplex exit motor
C12
Duplex end motor
C13
Upper cassette
C14
Lower cassette
C15
Pedestal upper cassette
C16
Pedestal middle cassette
C17
Pedestal lower cassette
C18
LCT
C21
Scan problem
C22
Lens problem
C23
Mirror motor
C26
Exposure lamp
C27
Scan motor
C33
Set up failure
C35
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41
Fuser thermistor or low temperature
C43
Fuser problem after warm-up
C44
Fuser problem after warm-up
C45
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01
Jam
E02
Fuser jam
E03
Jam at turn on
E04
Front door opened during copy cycle
E05
Registration jam
E08
Duplex unit jam
E11
Duplex jam
E12
Bypass jam
E13
Upper cassette jam
E14
2nd cassette jam
E15
3rd cassette jam
E16
4th cassette jam
E17
4th cassette jam
E19
CT jam
E21
LCT jam
E22-E25
Paper jams in copier
E71
ADF feed jam
E72
ADF transport jam
E73
ADF exit jam
E74
RADF jam
E75
ADF 2nd original jam
E81-E85
Sorter jam
E88
Jam after sorter
Toshiba 4570
Код ошибки
Описание
C01
Main motor drive problem
C04
Pedestal main drive problem
C05
Duplex drive problem
C11
Duplex exit motor
C12
Duplex end motor
C13
Upper cassette
C14
Lower cassette
C15
Pedestal upper cassette
C16
Pedestal middle cassette
C17
Pedestal lower cassette
C18
LCT
C21
Scan problem
C22
Lens problem
C23
Mirror motor
C26
Exposure lamp
C27
Scan motor
C33
Set up failure
C35
Developer at transfer/separator adjustment. This might mean a developer leak or shorted corona
C41
Fuser thermistor or low temperature
C43
Fuser problem after warm-up
C44
Fuser problem after warm-up
C45
Fuser sub-thermistor open. User problems. Reset required. Turn off power. Hold "0" & "8" keys while turning power on. Then press "8". Then press "9". Then press "print". You will read "3" in the display. Using the # keys, press "0" & "9" at the same time
E01
Jam
E02
Fuser jam
E03
Jam at turn on
E04
Front door opened during copy cycle
E05
Registration jam
E08
Duplex unit jam
E11
Duplex jam
E12
Bypass jam
E13
Upper cassette jam
E14
2nd cassette jam
E15
3rd cassette jam
E16
4th cassette jam
E17
4th cassette jam
E19
CT jam
E21
LCT jam
E22-E25
Paper jams in copier
E71
ADF feed jam
E72
ADF transport jam
E73
ADF exit jam
E74
RADF jam
E75
ADF 2nd original jam
E81-E85
Sorter jam
E88
Jam after sorter
Toshiba 4810
Код ошибки
Описание
C1
Scan not home
C2
Scan did not leave home
C3
Forward scan
C4
Forward scan (dual page mode)
C5
Scan limit
C6
Scan return
C7
Thermistor
CP
Motor lock
E1
Fuser jam
E2
Exit jam
E3
Jam
E5, E7
PF jam
Toshiba 4910
Код ошибки
Описание
C4
Cam switch
C5
Optics
C7
Thermistor or fuser
C8
Scan motor stays on
CE
Main board
C0
Dead battery
CP
Drive
E1
Jam
E2
Fuser jam
E3
Jam at turn on
E4
Door opened during copy run
Toshiba 5010
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB
ADF drive problem
CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC, ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 5020
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
ADD problem
A4
Sorter problem
A5
Board problem
A6
Sorter board problem
A7
ADF interface
A0
Communication problem between main board and PFC
C1
Board problem
C2
Board problem
C3
Board problem
C4
Board problem
C5
Optics locked or not initialized. Could be scan or lens/mirror
C7
Fuser thermistoe problem, or low temperature
C8
Scan motor won't shut off
CA
Main board problem
CB, CC
ADF drive problem
CD
BC RAM hardware
CE
BC RAM software
CP
Drive problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
E8
Jam in ADD (duplex)
E9
Jam in pedestal
EC, ED
ADF jam
EE
ADF exit/reverse jam
Toshiba 5110
Код ошибки
Описание
C0
Selector motor problems
C2, C3
Processor to subprocessor communication problems
C4
Paper feed cam motor drive problems
C5
Optic system initialization error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8
Scanner motor drive problems
CD
EPROM end of life
CE
EPROM defective or missing
CF
Development unit not properly installed or defective
CP
Main motor drive overloaded
E0
Used toner collection bottle full
E1
Paper jam in the machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E4
Front cover open during the copy cycle
E5
Cassette jam
E6
Paper jam at by-pass or defective sensor
Toshiba 5120
Код ошибки
Описание
C2
Signal to sub processor
C4
Cam motor
C5
Optics
C7
Thermistor or fuser problem
CD
Weak battery
CE
Battery disconnected
C0
DV select problem
CP
Drive
E1
Jam
E2
Fuser jam
E3
Jam after turning on
E4
Door opened during run
E5
Lower cassette jam
E6
Upper cassette
Toshiba 5510
Код ошибки
Описание
C2
Signal to sub processor
C4
Cam motor
C5
Optics
C7
Thermistor or fuser problem
CD
Weak battery
CE
Battery disconnected
C0
DV select problem
CP
Drive
E1
Jam
E2
Fuser jam
E3
Jam after turning on
E4
Door opened during run
E5
Lower cassette jam
E6
Upper cassette
Toshiba 5511
Код ошибки
Описание
C5
Initializing
C6
Home switch
C7
Thermistor
C8
Scan motor on
C9
Scan problem
E0
Waste toner bag full
E1
Jam
E2
Fuser jam
E3
Exit jam
E4
Front door
Toshiba 5540
Код ошибки
Описание
A0
Abnormal signal received at the optional paper feed tray
A1
Charge corona cleaner error
A2
Duplex functional problems
A3
Paper feed controller problems
A4
Sorter problem
A5
Communication lost with the sorter
A6
Communication problems with the sorter interface
A7
Communication problems with the feeder
A9
Exposure lamp blown, or bad contacts
C2, C3
Processor to subprocessor communication problems
C5
Optic system initialization error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
CB
Original feed motor overloaded in the feeder
CC
Original transport motor overloaded in the feeder
CE
BC RAM firmware problems
CF
Toner density error
CP
Main motor drive overloaded
E0
Used toner collection bottle full
E1
Paper jam in the machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E4
Front cover open during the copy cycle
E5
Paper feed jam in the paper tray
E8
Paper jam in the duplex unit
E9
Paper jam in the optional paper feed unit
EC
Original misfeed in the feeder
ED
Original jam in the feeder
EE
Original jam at the feeder inverter or exit area
Toshiba 5610, 5620
Код ошибки
Описание
C0
DV select switch or motor problem
C1-C4
Signal from sub processor (motor control board)
C5
Optics
C6
Home sensor
C7
Fuser
C8
Scan
CA
Sub processor
CD
Weak battery
CE
Battery disconnected
CP
Main motor
Toshiba 5910
Код ошибки
Описание
C2, C3
Processor to subprocessor communication problems
C4
Paper feed cam motor drive problems
C5
Optic system initialization error
C7
Fusing unit warm-up error, defective thermistor, fusing lamp or thermofuse
C8
Scanner motor drive problems
CD
EPROM end of life
CE
EPROM defective or missing
CF
Development unit not properly installed or defective
CP
Main motor drive overloaded
E0
Used toner collection bottle full
E1
Paper jam in the machine
E2
Paper jam in the fusing area
E3
Paper jam at start-up
E4
Front cover open during the copy cycle
E5
Cassette jam
E6
Paper jam at by-pass or defective sensor
E7
Paper jam in the machine
Toshiba 727, 728
Код ошибки
Описание
01
Scanner problem
02
Paper jam or path switch
03
Exit switch problem
04
Jam or paper on drum
05
Jam or false jam
Toshiba 7610
Код ошибки
Описание
C2, C3
Board
C4
Cam switch
C5
Optics
C7
Thermistor
C8
Scan motor
CD
EEPROM dead
CE
EEPROM
CP
Drum motor
E1
Jam
E2
Fuser jam
E3
Jam
E4
Interlock
E5
PF (lower cass.)
E6
PF (upper cass.)
Toshiba 7720
Код ошибки
Описание
A1
Spot motor
A2
Duplex guide
C0
Developer shift motor
C2
Signal main board
C3
Signal from main board
C4
Cam switch
C5
Optics have not moved
C7
Thermistor or cold warm up
C8
Scan motor
CD
Eprom dead
CE
Eprom
CP
Drum/fuser motor
E1
Jam
E2
Fuser jam
E3
Jam
E4
Interlock opened during copy cycle
E5
Paper feed jam from lower cassette
E6
Paper feed jam from upper cassette
Toshiba 7812, 7815, 7816
Код ошибки
Описание
C5
Initializing
C6
Home Switch
C7
Thermistor
C8
Scan motor
C9
Scan problem
CA
Scan switch
CC
ADF motor
E0
Waste toner bag full
E1
Jam
E2
Fuser jam
E3
Exit Jam
E4
Front door
Toshiba 7910
Код ошибки
Описание
C0
Paper feed cam switch problem
C2
Bad signal to main board
C3
Bad signal from main board
C5
Optics
C7
Fuser problem
C8
Scan motor staying on
CC
Document feeder problem
CE
Battery or memory problem
CP
Drive
E1
Jam
E2
Fuser jam
E3
Jam
E4
Door was opened during job
E5
Paper feed jam
Toshiba 8412
Код ошибки
Описание
C0
Cam motor
C1
Signal to color sub processor
C2
Signal to black sub processor
C3
Signal from color sub processor
C4
Signal from black sub processor
C5
Initializing
C6
Scan home switch
C7
Thermistor
C8
Scan motor
C9
Scan
CA
Document feeder
CB
Memory
CC
Document feeder
CE
Memory
E0
Toner bag
E1
Jam
E2
Fuser jam
E3
Exit jam
E4
Front
Toshiba 8510
Код ошибки
Описание
C0
Cam switches on cam motor
C2
Bad signal to sub processor
C3
Bad signal from sub processor
C5
Scan does not initialize
C7
Heater problem
C8
Scan motor stays on
CC
ADF
CD
Weak battery in memory EPROM
CE
Memory disconnected
CP
Drive problem
E1
Jam
E2
Fuser jam
E3
Jam
E4
Door opened during copy
E5
Feed jam
Toshiba 8812
Код ошибки
Описание
C5
Initializing
C6
Home switch
C7
Thermistor
C8
Scan motor on
C9
Scan problem
CA
Scan Switch
CC
ADF motor on
E0
Waste toner bag full
E1
Jam
E2
Fuser jam
E3
Exit Jam
E4
Front door
Toshiba 9110
Код ошибки
Описание
A1
Charge corona cleaner problem
A2
Duplex problem
C0
Cam motor
C1
Bad input to upper logic subprocessor
C2
Bad input to lower logic subprocessor
C3
Bad output from upper subprocessor
C4
Bad signal from lower subprocessor
C5
Optics problem at turn on
C6
Scan home switch
C7
Thermistor or fuser problem
C8
Scan motor stays on
C9
Scan problem
CA
Indicators
CB
Memory
CC
Motor stop signal present too long
CE
Software problem
E0
Toner bag full
E1
Jam
E2
Fuser jam
E3
Exit jam
E4
Door opened during run
Toshiba 9230
Код ошибки
Описание
A1
Charge corona cleaner
A2
Duplex problem
C1
Board problem. Input to upper logic subprocessor
C2
Board problem. Input to lower logic subprocessor
C3
Board problem. Output to upper logic subprocessor
C4
Board problem. Output to lower logic subprocessor
C5
Optics locked or not initialized. Could be scan or lens mirror
C6
Scan home switch
C7
Fuser thermistor problem, or low temp
C8
Scan motor won't shut off
CA
Indicators
CB
Memory
CC
Motor stop signal present too long
CE
Software
C0
Paper feed cam motor problem
E0
Waste toner full
E1
Jam
E2
Fuser jam
E3
Jam
E4
Front door was opened during copy run
E5
Feed jam
Если Вы не смогли найти своей модели в этом разделе, то есть вероятность, что Ваш аппарат является аналогом одного из представленных здесь. Проверить это можно в разделе "Совместимость".
Коды ошибок копиров ("ксероксов") Toshiba